Welcome Use
The user manual comes with off road electric
chariot scooter for the users’ reference when off road electric chariot scooter
(Smart Vehicle) are sold.
The user's manual
is applied to all the Smart vehicles off road electric chariot scooter made by
our factory. You may find that some function is different from what you
ordered.It is normal because of different series.
The content and technical specification in
this manual are valid when permitted to be printed. But our company has the
right to alter and change technical specification or design without prior notification.And
we will not assume any obligation.
To ensure our off road electric chariot
scooter brings you the best driving experience, the best way is to read the
user manual carefully, you will learn how to drive this future transporter.
After reading, please keep the user manual well so that you can refer to it any
time when you need.
The warranty card will come with off road
electric chariot scooter.You can find your warranty rights in the user
manual.Please read the user manual carefully so that you can know your rights
and responsibilities well.
Please maintain off road electric chariot
scooter according to the user manual so that you can keep the scooter in the
best condition.We have professional people who will supply you good after
service and answer any questions and problem you care.
Sincerely wish you
a nice driving!
Safety Instructions
For adults use only!
Please abide by your local traffic
regulations!
Please wear helmet, knee and elbow guards for
safety purposes.
Please read the relevant driving guidelines
in this manual!
Our company is not responsible for the
accident if you don not use it as the above request.
It is hard for us to list all associated dangers when driving and
maintaining off road electric chariot scooter, therefore, please be careful and
pay attention to the safety of yourself and others when riding.
The user manual
contains important safety information --- Please read carefully.
Contents
Chapter I
Introduction of off road electric chariot scooter...............4
Chapter II
Parts Explained..................................................5
Chapter III
Instruction of remote control of chariot scooter..............7
Chapter IV off
road electric chariot scooter Driving.....................8
Chapter V
Charging........................................................12
Chapter VI Maintenance
..................................................13
Chapter VII
Notice .........................................................14
Chapter VIII
Technical Data...............................................15
Chapter I Introduction of Off Road Scooter
The working principle of the two wheeled
Scooter is based on the basic principle called "dynamic stability"
which is the automatic balance ability of the vehicle itself. After judging
body posture position with a built-in precision solid gyroscope, the vehicles
electronic brain works out proper instructions through a sophisticated and
high-speed central microprocessor, the 36V-42Ah battery drives the motor to
balance the vehicle.
As a new transporter, off road scooter is
difficult to classify in the traditional way, some people think that off road
scooter should be a kind of double-wheeled Unicycle, while other people think
it should be classed as a power stand-up Scooter, with its uniaxial double
design which is different from the traditional biaxial double scooter, for
official road regulations, this transporter is called Electric Personal
Assistive Mobility Device (EPAMD)
The
vehicle is equipped with dual wheels, its width is as narrow as a normal adult
shoulder's width. It is 62 kg and battery-operated. It is not necessary to have
a brake or throttle during driving. When the driver leans their body forward, off
road scooter will run forward, when the body is upright, it will stop. It uses
the dynamic balance principle, as the body moves to change the center of
gravity so as to keep balance. Just as the human body stands and leans forwards
it can lose balance, but the body's natural instinct will maintain balance, the
dynamic stability replicates this. off road scooter uses the wheels to replace
the function of the feet, reproducing the high precision balance action of a
human, it is also cheap and convenient to use. The energy comes from two repeat
charging BTM batteries which are free from maintenance. If sufficient power is
supplied to your battery, the full charge capacity will last continuous for 5
hours driving, the driving range depends on the way you drive and ground
conditions, driving on grass and slopes will consume more driving power.
Chapter II Parts Explanation
Picture 1
1. Handle
Bar/Turning Pipe
(1)Used to control
and make the off road scooter turn left or right, turn around, rotate 360
degrees. It also has support function and can play a subsidiary role in keeping
body balance.
(2) The height is
adjustable. The driver can adjust it according to his or her own height to make
the handle bar comfortable.
(3)Lock the
steering rod after adjustment, then turn the handle bar to confirm that it has
had been locked.
(4)Above
adjustment of the handle bar/ turning pipe should be locked in position before driving.
(5)The turning
pipe can be taken apart easily for carrying or storage.
2. Power Switch
(1) The power
switch is used to turn on and off the power, when the power switch is on the off
road scooter will finish the initialization-settings.
(2) It is
dangerous to stand on off road scooter without turning on the power.
3. Pedal Switch (SAFE switch)
(1)The pedal can
be active up or down, it has a built in safety switch. off road scooter can
check whether someone on scooter by pedal switch.
(2) The pedal
switch is safety insurance, when driving, if the driver leaves the off road
scooter, the pedal switch will reset and then will stop after 3 seconds siren
alarm.
4. Battery LCD
Indicate the status of the battery. It is a LCD digital screen.
5. Illuminating light
This one is used to drive in dark
environment.
6. Warning Light
It is used to remind other people.
Chapter III Instruction of remote control of scooter
Picture 2
1. Functions of each button for the remote control
（1）Power
ON with a ticking voice, LCD power board indicated as per the percentage of
electricity 100% means full, 25% means need to charge in time.
（2）The
upper left button：Ticking
with a long voice at your 1st press for Unlock; Ticking with a voice at your
2nd press for Trailer Assistance; Ticking with a voice at your 3rd press for Cancel
The Trailer; If repeated, it is for the switch
between the mode of trailer and cancel.
（3）Click
the right corner key on the top，ticking
with a long voice for Lock
（4）The
lower left button：Ticking
with a voice at your 1st press for BEGINNER MODE which is 8-10 km per hour;
Ticking a voice for 3 times at your 2nd press for High Speed which is 18-20 km
per hour; Ticking a voice for 2 times at your 3rd press for Medium Speed which
is 12-15 km per hour; Re-press the button will recycle this operation.
（5）Button of the right at the
bottom：Start the Front Lamp and Rear
Warning Light
2.Additional Remarks ：
（1） Before shuting off
the power, if it is unlocked, then you don't have to unlock after turning on
the power, and you can stand directly on the balancing car.
（2） Before shuting off the power, if it is locked, then you
have to unlock after turning on the power, then you can start the balance car
and the default is medium speed.
（3）You
can't go ahead for a variety of speed switches when standing on the balanced car.
（4）Start
the Front Lamp and Rear Warning Light will can be operated no matter you have
already stand on the car or not.
3.An Adv. Of Alarming Horn & BUZZER:
（1）If
the balanced car is equipped with Alarming Horn, once started the car when it
is lock,the balanced car will automatically alarm or stand on the car can also
cause alarm no matter you drag car forward or backward,and a long Alarm Voice
will follows if it is not balanced when you start.
（2）For
the balanced car equipped with Alarming Horn,when the speed reached to the limit,the
alarm horn will drip, you should stop acceleration or deceleration and don't
forced acceleration.（When
speed alarm ticking, the voice will be short and fast and then a long Voice
Alert follows）
4.Adv. For The Buzzer Sounds
(1)If the buzzer repeated the sound of ticking at 1 time
which indicates car lean back too much.The correct behavior is to put the body to
be balanced, and then turn on the power switch.
(2)If the buzzer repeated the sound of ticking at 2 times
which indicates car lean forward too much.The correct behavior is to put the
body be balanced, and then turn on the power switch. After Power ON, the balanced
car regularly repeated "ticking" sound at 5 times at intervals which
indicates the balance car has not been unlocked or pedal switch is still
working（The switch does not rebound，which cause the poer of pedal
is still working）.
（2）When you get off, the
balancing car would have 3 seconds balanced to delay, and accompanied by the
voice of "ticking" at 4 times after the car stopped working. let the
initial position for the pedal of the balanced car .
（3）Initial position for pedal of each balanced car from factory is
recognized as balanced, if you started the balance（you feel not in
balanced enough or position is not suitable for yourself）,you can reset
the default initial position.
Method: Power ON, make the pedal be in
horizontal position, at the same time, press the BC key (two keys of the remote
control ) which will ring three times, which indicates already setted the
initial position.
2.Button
Operating
(1)Starting Scooter
Keep off road
scooter horizontal and power on it,
press Button D to unlock scooter,and you can hear one beep sound. Then you can
drive off road scooter, it is default mode. Default mode is Normal Mode.
(2)Pulling
Mode
After your pressing Button D,you can hear one beep sound(it means that
the scooter is unlocking),then you press Button D again,the scooter enters Pulling Mode. In this mode, the
scooter can be pulled by hand easily.When you press Button D the third time,the scooter will cancel Pulling Mode.
(3)Switching
Different Speed Mode
After your pressing Button B(scooter without driver on it),you can hear
one beep sound,scooter enters
Beginner Mode;When you press Button B
the second time,you can hear three beep sounds, scooter enters Default Mode;When you press Button B the third time,you can hear two beep sounds,scooter enters
Medium Mode.Switching different speed mode is valid only after driver leave scooter.
(4)Turning
ON/OFF Light
When you press Button C,the front and back light will light;If you press
Button C again,the light will stop.It is valid pressing the button when driver
on scooter .
Chapter IV off
road electric chariot scooter Driving
Driving the
off road scooter 2 wheel self-balance vehicle is totally different from
anything you may have driven before, off road scooter does not have a brake, accelerator or gear system. Please read the user
manual or get instruction from an experienced person before your first ride.
off road
scooter is very addictive once you enjoy the fun of driving, you will not help yourself
driving it whenever you get the chance, following these instructions will be
beneficial for your enjoyment.
Below description will be helpful to your driving.
Tip:We suggest you use Beginner Mode if you did not driver our off road scooter before.
1.Starting Operation
Hold the turning
pipe/handle bar with one hand, keeping the pedal upright ,turn on the power ,after
green light, orange light and red light flash at the same time, the green light
stay on continuous, It means starting success (refer to picture 3,4), hold the
handlebar firmly with two hands, then press Button D of remote control(refer to
picture 5,6).
Make sure the
pedal is on horizontal level when power on off road scooter.
Step on pedal with
another foot(refer to picture 7). The sequence is the left hand-right foot-left
foot -right hand or right hand -left foot-right foot-left hand. By this time
you will have stood on the balanced scooter. Stand upright without any body
move, just relax and keep your body balance, then scooter will still stay still
(refer to picture 8).
Picture 3
Picture 4
Picture 5
Picture 6
Picture 7
Picture 8
2. Driving straight forward
Lean
your body forward slowly using the centre of gravity, off road scooter will
move forward (refer to picture 9). The driving speed is controlled by the
leaning angle of your body. Lean forward more, off road scooter will go faster
and vice versa. For a stable driving, we suggest lean forward slowly. It is
dangerous for leaning forward suddenly. This is just like a sudden acceleration
when driving a car.
Picture 9
3. Braking,
Driving Backward
Driving backward is not recommended for the
driver's safety, because it is hard for you to see behind when driving. Turning
radius of off road scooter is zero, which you can easily achieve in a
continuous spin around 360 degrees on the spot. When you drive forward in a
straight line and you want to slow down or stop, you can lean backward or squat
down (the center of gravity backward). Lean slowly or smoothly backward is
helpful for slowing down and stopping safely (refer to picture 10).
Picture 10
Tip: Driving forward in a straight line you
just simply push the handle forward, then backward to slow down or stop.
4. Turning in Original Place, Turn Around and Rotate
360 Degrees
It is easy to turn the off road scooter when
driving. Keep the turning pipe/handle bar left-forward or right-forward to the
end, at the same time keep your body corresponding, left-forwarded or
right-forwarded as the trend of off road scooter (refer to picture 11 and
12).Thus you can easily achieve various turns. When the off road scooter faces
the right position, you only need return the pipe to the original position and
stand straight off road scooter will stop.
Picture
11 
Picture 12
5. Turning in Driving
off road scooter's turning range is
calculated automatically according to the driving speed, the speed is faster,
the turn range will be less to ensure safety of the driver, and it is stopped
by the turning pipe and body's corporation. To turn left, the turning pipe
should be swung smoothly to the left at the same time as your body leans left. The
angle of off road scooter's turn is decided by the swinging angle of the turning
pipe and the leaning of your body.
Tip: the actual turning is finished by the
above combination of actions, driving the off road scooter is like a
combination of riding horses and skiing, or the movement is like Michael
Jackson's dancing. off road scooter also is called a thinking car, which means
the driver can drive off road scooter according to his thoughts.
6. Driving in Bad Weather
off road scooter is not waterproof. Please do
not drive off road scooter on rainy days. It is easy to damage the motherboard and
the motor if water gets into the electrics.
off road scooter cannot be driven in the
snow.
off road scooter does not have night lights, so
please do not drive off road scooter in the dark
In China, off road scooter is hard to define,
so please don't drive on public roads used for motor vehicles .When driving on
the sidewalk, single driveway or public places, please comply with local
traffic regulations and the local bye laws.
Chapter V Charging
When you find the orange lamp and red indicator
is continuously on, it shows the battery needs to be charged. Please charge the
scooter when the electric capacity is less than 25%.
First, turn off
the power switch and use the specialized 24 V battery charger. Insert the plug
into off road scooter's charge jack, then connect the power. When charger is
connected the Red light will glow continuously, showing off road scooter is in
charge mode (refer to picture 13).
The charger has two indicators-the red light
means on charge, Green light means fully charged, pull out charger. The input
voltage of charger is 110-240v, output voltage is 25-27v, AC electric current
is 1.2 -1.5 A, The charger takes 8-10 hours to fully charge. When fully charged
the green light will be on continuously the charging electric current will then
decrease output. The charger will become warm when charging, so please keep in
suitable place.
Picture 13
Please keep
power switch of off road scooter off when on charge, otherwise, off road
scooter will cause power consumption, which is bad for charging.
Chapter VI Maintenance
All other items that are not mentioned below
should be done by a professional person or technician.
1. The Maintenance of Battery
Off road scooter use BTM free maintenance
battery. When you find the orange lamp and red lamp light continuously on, please
charge. Keep the charge time to no more than 15 hours. If you are not using off
road scooter for long periods, keep it charged, excessive discharge and re-
charge is bad for the battery's life and can even lead to having to scrap the battery.
(Suggestion: please keep it charged every month even you don’t drive it)
2. When not drive off road scooter
Please turn off the power switch then lock
the switch, in case of accidental starting.
3. Replacing Fuse
The fuse of off road scooter is
50A car fuse, the fuse maybe burned after overload or crashed sharply, when you
find that there is no action, and the indicator is off after switching on,
check the fuse if it is burnt out, you need to replace fuse, open the fuse
cover at the back of body with screwdriver, take out the fuse using clamp and
replace with a new fuse.
4. Fastening Nut of Tire
Pay attention to the big nut on the wheel, regularly check, if it is
loose tighten with a 21mm spanner to 108 torque.
5. Maintenance
of Tire
The normal air pressure is the basic
conditions to guarantee your safe driving .The standard tire pressure is 250
kpa = 2.5 bar = 2.55 kg/cm2 = 36.25 psi, that is what we recommend. It is
necessary to check the tire pressure regularly, under inflation and excessive
inflation will cause unequal tire wear, which influences comfort and mileage
and shorten the life of tire, under-inflated tires also influence power saving.
Also check for
cuts and splits which could cause the tire to deflate at a rapid rate, causing
injury to the rider.
6. Appearance Cleaning
It is necessary to keep the pedal and body of
off road scooter clean. Please clean the gravel, soil and mud off after you’re
driving. Don't use any corrosive chemical such as petrol to clean off road
scooter, you can clean off road scooter by using soft cloth and brush, don’t
wash off road scooter with water.
Chapter VII Notice
1.Balance Output of off road scooter
Computer balance will start immediately after
you press the pedal switch of off road scooter. If you keep pressing the pedal switch,
the computer balance will always start, the computer will keep balance for 5s
even if the pedal switch is restored when at a low speed. Please pay attention,
off road scooter will keep balance if the balance output function is ON. That
means putting this scooter on the road without driver on, it will go all by
itself.
2.off road scooter Parking
For temporary parking,
you can just turn on the balance output function and lean it against a wall or
step that can stop it from moving forward; for long time parking, you can
switch off the power and put the parking stand down. This parking stand can be purchased
from us independently.
3.Accident Water
Turn the power off
immediately if off road scooter falls into water accidentally. Do not drive it
again if you are not sure of the default. The off road scooter weighs 62kg. You
can pull it easily without power home and then contact us; we will give you
guide.
4.Lock Switch
Lock off road
scooter to prevent running by accident. Power off and then lock, when you power
on again, red light will flash 5 times, it means off road scooter is locked.
When you power on
and off road scooter starts to initialize, if you lock off road scooter at this
time, the locking will lead to pedal switch short circuit. off road scooter
will think that driver has stood on it and then start automatic balance. Please
do not drive under this situation.
Chapter VIII Technical Data
|
Net
Weight
|
62
kg
|
|
Dimension
|
91*54*72
cm
|
|
Max
cruise speed
|
18km/h
|
|
Max
load
|
125
kg
|
|
Max.
Mileage (after full charging)
|
30-35
km
|
|
Max
climb capability
|
35
degree
|
|
Min
turning radius
|
0
|
|
Charging
time
|
8
h-10 h
|
|
Battery
|
Dynamic
silicone PB battery: 3pcs,36V, 48Ah
|
|
Power
|
Two
imported DC Motor, DC servo drives
|
|
Voltage
|
100
v-240 v
|
|
Max
Power
|
1600
watts (2*800 w/pc)
|
|
Lifetime
of battery
|
1-3
years
|
|
Tire
|
19*7-8inch
shock-absorb tire
|
|
Wheel
|
Superior
integrated aluminum magnesium alloy
|
|
Height
of handle
|
80-110
cm adjustable
|
|
Height
of footplate
|
10in/26cm
|
|
Specification
of footplate
|
11.5×25
in / 16×40 cm
|
|
Max.
Height above ground
|
13
cm
|
|
Standard
Pressure
|
250
kpa
|
|
Certificates
|
CE
& ROHS &FCC
|
Meet us in canton fair 2.1Y67 from 15th to 19th Oct.
Add: F5 2nd Building ,Kerda Industrial Park ,Zhonghao1st Road,Bantian LongGang District,Shenzhen,China.
Email:lisa@sunnyti
Skype:bethyzhu
Tel: 0086-755-21500972
Mob:0086-13423809666
没有评论:
发表评论